气液螺旋环状流压降特性研究

考虑旋流衰减的影响，对气液螺旋环状流的压降特性进行研究并推导出了螺旋环状流压降预测模型。定义压降旋-直比系数为气液两相螺旋环状流和气液两相直流的压降之比，以此来表征旋流衰减对压降的影响。基于量纲分析的方法对压降旋-直比系数进行分析，推导出其表达式，压降旋-直比系数依赖于Lockhart-Martinelli 参数和气相Froude数变化。最终，得出了气液两相螺旋环状流的压降预测模型。在50 mm内径的水平管内对螺旋环状流的压降特性进行了实验研究，其中气相表观流速变化范围为10~16 m/s，体积含液率（LVF）变化范围为0.6%~4.8%。通过与实验数据进行对比，压降预测模型的相对误差在±15%以内，为工程应用提供了参考。     

A directional control method for interface flow considering static voltage stability

A directional control method (DCM) for power flows on a set of interface lines between two regions of power system considering static voltage stability margin is developed in this paper. A surface approximation approach is firstly used to obtain the relationship between the interface flow solution and the generation direction of generator (the portion of generation variation in each participating generator to satisfy the desired power increase on the interface and the system loss). Then, an optimization model is built to determine the optimum dispatching scheme of generators. This method not only can control the total power on the interface to satisfy the power demand but also can realize the directional control of power on each interface line based on the needs of operation. The proposed DCM is further extended to determine the optimum dispatching scheme of generators for maximizing the interface flow margin (IFM), which is the active power margin of the key transmission lines between two regions of power system constrained by static voltage stability. A modified continuation power flow (MCPF) is used to show and evaluate the impacts of the DCM on the IFM. The New England 39-bus system and the IEEE 300-bus system have been employed to verify the effectiveness of the DCM.     

中高压变频器冷却方案比较和选型分析

随着电力电子器件的发展,性能优异的中高压变频器在各行各业中得到越来越广泛的应用,能否处理好变频器的散热问题是其长期稳定运行的关键。分析了中高压变频器热量产生来源,并从技术可行性、可靠性、经济性等角度对不同冷却方案的特点进行比较,并结合实际的工程案例,给出合理的变频器冷却方案选型建议,可作为工程电气设计时中高压变频器冷却方案选型参考。     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

Fraud detection in registered electricity time series

This paper analyses time series without the seasonal component of consumers’ power consumption at low voltage in order to detect fraud and illogical consumption by customers. Statistical process control is used, where the process represents the process of using electricity. XMR charts are used to indicate major changes (decrease) in registered customers’ consumption. Verification of this method was tested on time series of a set of customers who were caught stealing during a time series. It shows that symptoms of non-random factors in time series of customers are revealed in a high percentage, which indirectly confirms the method’s ability to successfully detect electricity fraud.     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Design and performance study of phase‐locked loop using fractional‐order loop filter

The present work reports the realization of an analog fractional‐order phase‐locked loop (FPLL) using a fractional capacitor. The expressions for bandwidth, capture range, and lock range of the FPLL have been derived analytically and then compared with the experimental observations using LM565 IC. It has been observed that bandwidth and capture range can be extended by using FPLL. It has also been found that FPLL can provide faster response and lower phase error at the time of switching compared to its integer‐order counterpart. Copyright © 2014 John Wiley & Sons, Ltd.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.